@article { author = {Danaie, M and Khani, S and Noorozzadeh, E and Vahdani, M}, title = {Improving the performance of cadmium telluride solar cell (CdTe) with different buffer layers}, journal = {Iranian Journal of Physics Research}, volume = {19}, number = {1}, pages = {139-147}, year = {2019}, publisher = {Isfahan University of Technology, The Physics Society of Iran}, issn = {1682-6957}, eissn = {2345-3664}, doi = {10.29252/ijpr.19.1.15}, abstract = {In this paper, the performance of the buffer layer of Cadmium Telluride (CdTe) thin film solar cell was optimized using SCAPS software. At first, five different buffer layers including CdS, In2S3, ZnO, ZnSe and ZnS with variable thicknesses from 10 to 100 nm have been replaced in the structure of the solar cell and it has been observed. As the thickness of the buffer layer is increased, the efficiency decreases.Due to the increase of thickness light absorption in the structure is increased and less light is absobed in CdTe layer. The reason behinf this incident is described physically. Then the performance of the solar cell with different buffer layers is compared, and the effect of each of the layers on the four main parameters of the solar cell has been investigated. Simulation results show that the ZnS buffer layer has a higher efficiency in all thicknesses than other materials which originates from the fact that the bandgap of this material is bigger than other materials.}, keywords = {solar cell,thin film,Buffer layer,band gap,absorbing layer}, title_fa = {بهبود عملکرد سلول خورشیدی کادمیوم تلوراید (CdTe) با لایه‌های بافر مختلف}, abstract_fa = {در این مقاله عملکرد لایه بافر سلول خورشیدی لایه نازک کادمیوم تلوراید (CdTe) با استفاده از نرم‌افزار SCAPS بهینه‌سازی شده است. در ابتدا پنج لایه بافر مختلف از جمله CdS، In2S3، ZnO،ZnSe  و ZnS با ضخامت‌های متغیر از 10 تا 100 نانومتر در ساختار سلول خورشیدی جایگزین شده‌اند و مشاهده شده است که هر چقدر ضخامت لایه بافر افزایش یافته است، میزان بازدهی کاهش می‌یابد، زیرا با بیشتر شدن ضخامت لایه بافر، جذب نور در این لایه بیشتر شده و میزان کمتری از نور در لایه جاذب (CdTe) جذب می‌شود. سپس عملکرد سلول خورشیدی با لایه‌های بافر مختلف با هم مورد مقایسه قرار گرفته و تاثیر هریک از لایه‌ها بر چهار پارامتر اصلی سلول‌خورشیدی بررسی شده است. نتایج نشان می‌دهد که لایه بافر ZnS تقریبا در تمام ضخامت‌ها دارای بازدهی بالاتری نسبت به سایر مواد می‌باشد، که دلیل این امر بزرگتر بودن شکاف باند این ماده نسبت به سایر مواد می‌باشد.    }, keywords_fa = {سلول خورشیدی,لایه نازک,لایه بافر,شکاف نواری,لایه جاذب}, url = {https://ijpr.iut.ac.ir/article_1422.html}, eprint = {https://ijpr.iut.ac.ir/article_1422_36f0d8d1b92c8405e4f73e14f388a987.pdf} }