نویسندگان

1 پژوهشکده ذرات و شتابگرها، پژوهشگاه دانش‌های بنیادی

2 پژوهشکده فیزیک و شتابگرها، پژوهشگاه علوم و فنون هسته‌ای

3 گروه کاربرد پرتوها، دانشکده مهندسی هسته‌ای، دانشگاه شهید بهشتی

4 . پژوهشکده ذرات و شتابگرها، پژوهشگاه دانش‌های بنیادی

چکیده

هدف اصلی در طراحی و ساخت شتاب‌دهنده‌های خطی الکترون با بسامد رادیویی دستیابی به باریکه‌های الکترونی با کیفیت مطلوب‌تر، توان و انرژی بالاتر با صرف توان بسامد رادیویی کمتر است. راه رسیدن به این هدف انجام تحقیقات در زمینه طراحی، ساخت، اندازه‌گیری و تنظیم بسامدی کاواک شتاب‌دهنده‌ها می‌باشد. دانش‌های بنیادی اولین تلاش ایران برای ساخت شتاب‌دهنده‌های بسامد رادیویی است. در این مقاله، پس از بررسی مختصر روش ساخت، اندازه‌گیری و تنظیم بسامدی یک ساختار دوره‌ای بارگذاری شده با قرص (دیسک) مورد بررسی قرار گرفته و نتایج قبل و بعد از تنظیم بسامدی به همراه جزئیات طراحی و راه اندازی سیستم مورد استفاده برای اندازه‌گیری اختلالی پروفایل میدان الکترومغناطیسی ارائه شده است

کلیدواژه‌ها

عنوان مقاله [English]

Design and construction of cavity frequency measurement and tuning systems of traveling wave electron linear accelerator

نویسندگان [English]

  • S Ahmadiannamin 1
  • F Ghasemi 2
  • F Abbasi Davani 3
  • M Lamehi Rachti 4
  • M Shirshekan 4
  • M Bahrami 4

1

2

3

4

چکیده [English]

The main purpose for designing and constructing electroradio frequency linear accelerators is to reach better beam quality with higher power and energy by lower RF power consumption. The main step for this purpose is doing research and development in the area of designing, constructing, measuring and tuning of accelerator RF cavities. Institute for Research in Fundamental Sciences (IPM) linear accelerator projecta is the first Iranian project for construction of electrolinear accelerator. In this paper, a brief introduction to construction procedure has been given. Then, the measurement and tuning of a disk-loaded periodic structure before and after tuning was reported. In addition, the detailed design and measurement setup for electric field measurement by perturbation method was investigated

 

کلیدواژه‌ها [English]

  • disk-loaded structure
  • constant impedance
  • accelerator cavity
  • bead pull setup
  • Slater perturbation method
  • tuning
1. R F Post and N S Shiren, Review of Scientific Instruments, 26 (2) (1955) 205.
2. M Chodorow, E L Ginzton, W W Hansen, R L Kyhl, R B Neal, and W K H Panofsky, Stanford High‐Energy Linear Electron Accelerator (Mark III). Review of Scientific Instruments, 26 (2), (1955) 134.
3. J Gao, Analytical approach and scaling laws in the design of disk-loaded travelling wave accelerating structures. Paris-11 Univ., 91-Orsay (France). Lab. de l'Accelerateur Lineaire (1993). .
4. T P Wangler, “RF Linear accelerators”, John Wiley & Sons (2008).
5. W Fang, D Tong, Q Gu, and Z Zhao, Design and experimental study of a C-band traveling-wave accelerating structure. Chinese Science Bulletin, 56 (1), (2011) 18.
6. G A Loew, R H Miller, R A Early, and K L Bane, Computer calculations of traveling-wave periodic structure properties. Stanford Univ., CA (USA) (1979).
7. W Fang, Q Gu, D Tong, and Z Zhao, Design optimization of a C-band traveling-wave accelerating structure for a compact X-ray Free Electron Laser facility. Chinese Science Bulletin, 56 (32) (2011) 3420.
8. L C Maier Jr, and J C Slater, Journal of Applied Physics, 23(1), (1952) 78.
9. C W Steele, IEEE Transactions on, 14(2), (1966) 70.
10. S Ghosh, S Seth, A Mandal, and S S Som, Bead-pull measurement using phase-shift technique in multi-cell elliptical cavity. In Conf. Proc. 110904, IPAC-2011-MOPC088, (2011) 280.
11. L C Maier Jr, and J C Slater, Journal of Applied Physics, 23 (1), (1952) 68.
12. W J Gallagher, “Measurement techniques for periodic structures,” Microwave Lab., Stanford Univ., Stanford, CA, Rep. 767, (1960).

تحت نظارت وف ایرانی